Bauer Ltd Catfish

Bauer Limited Production was founded by Cord Bauer. Cord is the designer and developer of the Bauer Catfish. This Miata Kit Car uses a 1990 to 2005 Miata. As with most kit cars Bauer recommends you start with the best kit car donor possible. They also recommend the 1.8L engine option.

The base price of the Miata Based Catfish kit car is $13,900 and included the following…

Frame & hard panels—High quality U.S. made seamless DOM tubing is used throughout, with main spars and lattices at 1.5” O.D. Each chassis is jig welded and designed to fit directly onto 1990-2005 Miata sub-frames that are in good condition. The main body is MIG welded, while the exposed roll hoops are TIG welded. Full TIG welding is an option. No customer welding or bending is required. The front clip acts as a replaceable front frame support. It also holds the NB-style radiator as well as the front bodywork. The rear bolt-on clip holds bodywork and the optional diffuser. Brakes, suspension, fuel and wiring are simple to install. Mounts for four, five or six point harnesses are included.

Includes single roll hoop
Engine bay sized for many engine options, including LS, Ford V8, SR20DET, F20C/22C, 3S-GTE and many others. The first, best choice is the stock Miata (120-150hp) or Miata with forced induction (220whp +).
Front clip holds NB-style radiator and allows lots of room and airflow for intercooler placement. The body mount on the front clip doubles as the front diffuser support mount.
The frame also includes mounting points for the rear sub-frame support brackets.
Un-coated finish to allow for welding customer options prior to assembly
New grade 10.9 hardware is included for assembly. Donor suspension hardware is retained.
Floor—floor panels are laser-cut and pre-drilled for assembly. The center floor panel is removable for access to the drive line. The front panels rest under the radiator and tie together the front bodywork with the front K-member.
Complete aerodynamic flat bottom: Left and Right floor pan, with removable center for drive line access. There is also a front Flush Splitter that fits from the nose to the engine (an extended Splitter is an option), and a driver and passenger secondary interior floor to protect the occupants.

Bauer Catfish Miata Kit Car 3

The Catfish is designed to be extremely easy to build. Tabs are included to mount all the bodywork to the frame, and most bodywork will ship partially pre-installed (Pre-Assembled package), meaning that the bodywork is pre-fit and properly sorted. Customers will simply take the bodywork off, start the build, and then re-fit the bodywork and add final mounting points as needed. The Quick Start package adds seam sealing and complete mounting of the interior panels and bodywork that will take days off your build time.

Frame brackets are included for all pedal controls, suspension, gas tank, radiator, seats, safety harness and obviously the fitment of the Miata sub-frames. While many tuners will use our kits as a basis for their race cars, no welding is required to turn the base model into a potent street car.

All Standard composite construction using woven S-glass, with carbon reinforcements where needed. Standard 10.9 grade installation hardware is included. The bodywork is finished in a gel coat that’s ready for light sanding in preparation for paint. The bodywork is very light, with the main body side panels that run the length of the car weighing 20lbs each. When the body is fastened together, it becomes exceptionally rigid.
Firewall—the front firewall is made of steel & aluminum plate, and protects the driver and passenger from the engine. The rear firewall is made of aluminum to meet NASA and SCCA rules.
Side Panels, driver and passenger—These run the length of the car and include mounting areas for lighting. The driver side includes room for the exhaust. Internal bulkheads are found at the firewall location for safety and stiffness. Mounting points are at the bulkhead, floor, shock towers, rear deck, rear bumper and front grille.
Hood—this is a large piece that’s nearly half the length of the car. It mounts in front with AeroCatch and Quik-Latch patented hardware (supplied). A bonded interior hood structure keeps the hood stiff.
Grille—this mounts to both side panels and the aluminum floor. The side air intake areas can be used to funnel air to the front brakes, and the air slot directly below the hood can be used as a cold air or intercooler intake.
Rear Bumper & License Light panel—the base model includes a full bumper with a rear indent that shows where the diffuser would mount. This area is easily removed for use with the diffuser. The light panel holds the license plate and the reverse lights (included).
Rear Deck—the rear deck goes from behind the seats to the tail. The roll hoops exit from the deck, as does the gas cap.
Roll Bar Cover—these are optional parts, and are designed to smooth the air flow off the roll hoop.

Bauer Catfish Miata Kit Car 2

The standard interior body panels are made of sheet aluminum, and are designed to be used with stock or aftermarket seats. The Catfish has more room than a Miata for larger race seats, and more leg room than a standard Miata. Provisions are also made for the use of the stock gauge panel and emergency brake. All aluminum panels are pre-cut and pre-drilled with mounting holes. Ask about having your car shipped with all interior and exterior panels pre-fit.
Interior sides—the aluminum side panels can be painted, wrapped (standard and aluminum colors), or covered in micro-suede or similar fabric. Dimple die holes that reference the race interiors of classic British race cars are optional.
Secondary floors—made of aluminum plate, these pieces run from the firewall to the seats. They are intended to offer extra protection to the driver and passenger. Hardware is included.
Center tunnel—molded from the original SEMA car and made from composite material, the center tunnel matches the curve of the outside body line and has provisions for the shift boot and emergency brake.
Rear panel—the rear aluminum panel is a single sheet of aluminum, and acts as the rear firewall.
Dash—this is a simple bolt-in part that is designed to make use of the stock gauge panel.

Wiring can be the most daunting part of an assembly process. We offer body wiring harness kits from $500 to complete racing mil-spec wiring kits that replace the entire stock harness. Contact us for details.

Brake lines–replacement hard lines are available should you want to swap your old lines for new, or if damage has rendered your hard lines inoperative.

DOT approved (SAE compliant) Headlight and Taillight package, including reverse, license and auxiliary lighting. All auxiliary lights are super-bright, low power LED lights.
Clear polycarbonate headlight bucket cover, pair. The entire headlight is a custom design, and does not use parts intended for some other car.
TIG welded custom stainless steel headlight shrouds with hardware included
Optional–Driver and passenger Brooklands-style fly screen kit
Optional–Full Width DOT safety glass windshield including frame, mounting brackets and wiper brackets
Hardware Installation packet, including body brackets, AeroCatch & Quik-Latch hood quick release fasteners, rivets, buttons and latches
TIG welded custom Exhaust side pipe. This is a light weight straight through perforated core exhaust, and is built with light weight 22 gauge 304 stainless throughout. The muffler itself weighs 5lbs. The exhaust tip is TIG welded by hand, and includes an internal perforated core. Mid-pipe not included.

Included–Exhaust street insert (lowers db level)
Included–Custom Stainless Steel Heel and Kick Plates
Included–Catfish Stainless Key Chain and Bottle Opener
Included–Catfish Custom Stainless Steering Wheel Center
Optional–Full TIG welded chassis
Optional–wiring harness kits, from simple to complete
Optional–brake hard line kits
“E & O E” (Errors and Omissions Excepted), Other items To Be Determined (TBD) at the time of production

Bauer Limited Production
417 E. Carmel St.
San Marcos, CA 92078